Skip to content
5,000+ phones repaired • FREE tracked Royal Mail postage • Warranty on every repair • Need help?
5,000+ phones repaired FREE tracked Royal Mail postage Warranty on every repair (terms) Harlow workshop • UK-wide postal repairs Need help? Contact us

iPhone AirDrop Not Working? Checks to Try in Order

21/11/2026 by James Waterston

If your iPhone’s AirDrop isn’t working, check Wi-Fi, the other wireless connection and the receiving setting on both devices first. Then turn off Personal Hotspot, bring the devices together and try sending one photo.

Seeing someone’s name but getting stuck on “Waiting” is frustrating, but it doesn’t automatically mean your phone needs repairing. We recommend working through these checks in order, testing after each change so you know what helped.

Key takeaways

  • Turn on the required wireless connections on both devices, then select Everyone for 10 Minutes on the receiver.
  • Keep each screen awake, unlocked and close together. Disconnect Personal Hotspot, temporarily pause any VPN and turn off Do Not Disturb.
  • Restart and update before considering a network reset. If wireless problems began after an impact, look for faults beyond AirDrop.

1. AirDrop not working? Start with the radios

AirDrop needs working wireless radios on both devices. Checking only the sending iPhone leaves half the connection out of the diagnosis.

Switch Wi-Fi and Bluetooth off properly

On each iPhone or tablet, open Settings > Wi-Fi and Settings > Bluetooth. Switch each off, wait about ten seconds, then switch them back on.

Use Settings for this check. Control Centre buttons can disconnect connections without fully switching off the radios.

You can also switch Airplane Mode on briefly, then off again. Afterwards, manually confirm the radios are on, because Airplane Mode can remember earlier wireless settings.

On a Mac, check both connections in System Settings. Apple’s AirDrop connection guidance confirms that both radios need to be enabled.

Remove competing connections and distractions

Turn off Personal Hotspot on either device. On an iPhone, open Settings > Personal Hotspot and switch off Allow Others to Join. Temporarily disconnect any VPN too, because its network rules may interfere with local connections.

Also switch off Do Not Disturb or another Focus mode on both devices for one comparison test. We treat this as a low-impact check, rather than proof that Focus caused the failure.

Keep both devices awake and unlocked. Put them side by side, without walls or other obstacles, rather than testing near the roughly 9 to 10-metre limit commonly suggested for troubleshooting.

An illustration of an iPhone, iPad, and MacBook connected by abstract wireless signals.

2. Check receiving permissions and contact details

A receiving setting can stop a perfectly healthy device appearing. We recommend testing temporary visibility before changing contact records.

Select Everyone for 10 Minutes

On the receiving iPhone or iPad, open Settings > General > AirDrop and select the broader visibility option.

You can also open Control Centre, press and hold the connectivity panel, tap AirDrop in the control menu and choose the broader visibility option. Apple’s AirDrop receiving instructions show this route.

Start your test promptly, because the option is temporary. If troubleshooting takes longer than ten minutes, select it again before retrying.

On a Mac, open Finder > AirDrop and change “Allow me to be discovered by” to the broader visibility option. The computer’s wording differs from the timed iPhone and iPad option.

Correct Contacts Only identification

If the broader visibility option works but contact only doesn’t recognise the sender, check the contact details first. Apple labels this setting “Contacts Only”.

The receiver’s contact card for the sender needs the email address or mobile number associated with the sender’s Apple Account. A saved name alone doesn’t establish that match.

Open Contacts on the receiving device and inspect the sender’s entry. Correct an outdated number or missing email address, then switch back to Contacts Only and repeat the test.

Avoid changing several contact cards at once. One corrected entry and one fresh transfer give you a much clearer result.

Once testing is finished, use the receiving option you normally prefer rather than leaving broader visibility enabled unnecessarily.

3. If a device appears but sending stalls

Seeing the recipient confirms that something is discoverable. It doesn’t tell you which setting or device is preventing completion.

An illustration of an iPhone and a MacBook on a wooden table in a living room.

Check restrictions and available storage

Check content restrictions under Settings > Screen Time > Content & Privacy Restrictions > Allowed Apps & Features and make sure AirDrop is allowed. Older software may label the last menu Allowed Apps.

If you manage the device and have permission, temporarily disabling Content & Privacy Restrictions can help isolate a restriction. Restore them afterwards. For a work or school device, ask its administrator rather than trying to bypass management controls.

Next, open Settings > General > iPhone Storage on an iPhone, or the tablet’s storage settings. Check the receiver’s available storage space before retrying a large video.

Free space by removing content you no longer need. Don’t delete the only copy of important photos to make room.

Run a small, controlled transfer

Cancel the stalled attempt, then send one ordinary photo. Watch the receiver for an Accept prompt and keep both screens awake throughout the test.

If that works, retry the original file. A successful photo transfer followed by one failing video gives you a narrower problem to investigate.

If possible, introduce a third Apple device. Test the original iPhone with that device, then test the original receiver separately.

Keep the file and settings consistent. If failures follow one device across different partners, focus further troubleshooting there rather than resetting everything.

4. For Mac transfers, check Finder and the firewall

For transfers between an iPhone or tablet and the computer, leave it awake with Finder > AirDrop open. Select Everyone for discovery, then send the small test photo again.

For transfers to an iPhone, set the phone to the broader discovery setting for 10 Minutes, keep it unlocked and watch for the incoming request.

Next, inspect System Settings > Network > Firewall > Options. Make sure Block all incoming connections is turned off. This path also appears in an Apple Support Community firewall discussion.

You don’t need to disable the entire firewall as your first move. Check the specific blocking option instead, and respect any organisation-managed security policy.

Temporarily disconnect its VPN as well. If only the computer fails with several different Apple devices, investigate its settings rather than repeatedly changing the iPhone.

After an incoming transfer completes, check the Downloads folder before assuming the file disappeared.

5. Restart and update before deeper resets

If the reversible checks haven’t helped, move on to software recovery. We recommend changing one device at a time where practical.

Restart both devices and install updates

A full reboot means powering the device off, rather than merely locking its screen.

On an iPhone with Face ID, hold the side button and either volume button until the power-off slider appears. Release the buttons, slide to switch off, then turn the phone back on once it has shut down.

You can also use Settings > General > Shut Down. Power the receiver off and on. Shut the computer down, then turn it back on.

In general settings, check Settings > General > Software Update on iPhone or iPad. On a computer, use System Settings > General > Software Update. Install available updates after backing up important data.

Keep a network reset as a last resort

A network reset is an optional deeper step, rather than a required AirDrop fix. Consider it only after checking receiving permissions, restrictions, and updates.

Reset Network Settings clears saved Wi-Fi networks and passwords, so have those details available first. It doesn’t erase your photos or apps, but reconnecting afterwards can be a bit of a faff.

Be careful not to confuse it with Erase All Content and Settings.

We wouldn’t start with a factory reset for an isolated AirDrop problem. First establish whether the fault affects one receiver, one file or every wireless connection.

6. Look beyond AirDrop if problems followed a drop

An isolated failed transfer doesn’t diagnose damaged hardware. However, an iPhone component fault after a drop becomes more plausible when other wireless functions also misbehave.

We’ve seen an apparently undamaged iPhone with a connection stuck searching and another wireless function unavailable. That combination deserves broader diagnosis, even when the glass looks fine. Our advice on Bluetooth problems after a drop covers the related warning signs.

Also test ordinary wireless connectivity and a familiar wireless accessory. If connectivity fails across several networks, our iPhone Wi-Fi troubleshooting checks help separate a wider connection problem from an AirDrop-only issue.

The same approach helps with iPad fault diagnosis: establish which functions fail before deciding what needs attention.

A clean-looking case doesn’t rule out internal impact damage. Equally, one failed AirDrop transfer isn’t enough evidence to recommend replacing a component.

Back up important data while the device remains usable. Avoid opening it or pressing the frame to try to restore a connection.

Frequently asked questions

Do AirDrop devices need Bluetooth pairing?

No. You don’t need to pair the iPhone and receiver in wireless settings. AirDrop handles its own connection when the devices are discoverable and the necessary wireless functions are enabled.

If you’re repeatedly trying to pair two iPhones like headphones, return to the AirDrop receiving settings instead. Pairing isn’t part of the normal transfer process. Likewise, forgetting your headphones won’t resolve an AirDrop contact-identification problem.

Can an iPhone AirDrop directly to Samsung or Google Pixel?

AirDrop is for compatible Apple devices, so a Samsung or Google Pixel phone won’t appear as an AirDrop receiver.

That absence doesn’t indicate a component fault on either phone, even if you first notice it after a drop. Use a sharing method supported by the devices, such as a shared cloud link. Keep hardware troubleshooting separate unless the Android phone also has its own wireless symptoms.

Get a clear result before assuming a repair

We recommend finishing with one small transfer, followed by the file that originally failed. Once both arrive, restore your normal receiving settings and any VPN or Focus preferences you paused.

If several wireless functions still fail, especially after a drop or liquid exposure, a diagnosis is the sensible next step.

At Phone Repair Direct, you can arrange help through our Harlow repair workshop. Tell us which devices failed and which checks you’ve already tried.